Select your actual input and output devices, use push-to-talk in noisy rooms, place the microphone close to and slightly beside your mouth, lower playback enough to hear footsteps, and make a test recording before entering a busy room.
1. Choose the correct input and output
Many 'nobody can hear me' problems begin with the wrong device. In TeamSpeak's audio settings, Capture should be your actual microphone, and Playback should be your headphones or speakers. Default works well only if Windows has the same device selected as its default.
- For a USB headset, choose the headset by name instead of the laptop microphone.
- If an HDMI monitor appears as an output but you want headphone audio, select the headphones manually.
- After disconnecting and reconnecting a Bluetooth or USB headset, check the device selection again.
- Headphones are better than speakers for group gaming because friends' voices do not feed back into your microphone.
2. Push-to-talk or voice activation?
| Mode | Best suited to | Important note |
|---|---|---|
| Push-to-Talk | Noisy rooms, mechanical keyboards, fans, or busy households | Choose a key that does not interfere with movement, shooting, or buying in-game. |
| Voice Activation | A quiet room and a nearby microphone with a steady voice level | Set the threshold using your normal voice, not a shout or a whisper. |
| Continuous transmission | Testing or special uses only | Not suitable for public rooms: it sends every background sound. |
For CS2, push-to-talk is the safer choice. If you prefer voice activation, test silence, typing, and normal speech. The threshold should be above the room's background noise but below your quiet speaking voice.
3. Microphone placement matters more than filters
Keep a headset microphone roughly two to four finger-widths from your mouth and slightly to one side, so bursts of air from P and B sounds do not hit it directly. A desktop microphone should be closer to your mouth than to your keyboard. Behind the keyboard beside a monitor, it may pick up clicks more loudly than your voice.
High gain boosts more than your voice: it also amplifies fans, street noise, and the keyboard. Move the microphone closer, then increase input until normal speech is clear without loud speech becoming distorted.
4. Use noise and echo reduction in moderation
If friends' voices are not coming out of speakers into your microphone, there is less chance of echo in the first place.
Useful for a steady fan, but strong suppression can cut off word beginnings or endings and sound unnatural.
It can raise a quiet voice, but it may also amplify room noise during silence.
If you enable several filters together, you will not know which one improved or worsened the sound.
The exact names and locations of these settings may vary by TeamSpeak version, operating system, or audio plugin. The order stays the same: device and microphone placement first, volume second, and only the filters you need last.
5. Balance TeamSpeak and game audio
In CS2, louder is not always better. If friends' voices cover footsteps and reload sounds, lower TeamSpeak playback a little. If calls get lost during gunfire, first raise that user's volume or playback slightly. Turning up both the game and TeamSpeak usually just tires your ears.
- Set your usual game volume on a practice map.
- Ask a friend to make a few short calls at their normal speaking volume.
- Adjust playback until speech is clear and nearby footsteps remain audible.
- Adjust an unusually quiet or loud user separately instead of changing everything for one person.
6. Choppy audio is not always a microphone problem
For robotic, interrupted, or delayed audio, check the network too. Ethernet is usually steadier than congested Wi-Fi. On Wi-Fi, stay near the router and use a less crowded band if possible. Pause heavy uploads, cloud sync, game downloads, and unnecessary VPN use during testing.
- Only one person's audio is poor: their device or connection is a likely cause.
- Everyone cuts out at once: check your connection and network route.
- Problems appear only while uploading or streaming: upload saturation and packet loss are likely.
- Changing the server codec does not fix real packet loss. Address the connection first.
What does AmoHa room quality 10 mean?
AmoHa rooms are set to voice quality 10, but the result still depends on your microphone, placement, input level, and internet connection. A high-quality room cannot fix a distant microphone, poor gain settings, or unstable Wi-Fi.
For a real test, connect to amoha.ir, check your voice with a friend in a quiet room, then enter the gaming section. If a problem remains, the TeamSpeak support channel can start a private conversation.
A one-minute pre-game checklist
- The correct microphone and headphones are selected.
- Normal speech is clear and louder speech does not distort.
- Keyboard and fan noise do not activate transmission during silence.
- Your push-to-talk key does not conflict with important game controls.
- Friends' voices do not drown out footsteps.
- Unnecessary downloads, uploads, and VPN connections are paused during testing.
Frequently asked questions
Why can everyone hear my keyboard?
The microphone may be closer to the keyboard, gain may be too high, or the activation threshold may be too low. Fix microphone placement first, then adjust gain or the threshold.
Why are the beginnings of my words cut off?
The voice activation threshold may be too high, or noise processing may be too aggressive. Test quiet sentences and change only one of these settings at a time.
Why do I hear my own voice with a delay?
Your voice is usually coming out of someone else's speakers or headset and back into their microphone. Use headphones, lower playback, and identify the microphone causing the echo.
Will an expensive microphone solve everything?
No. A mid-range headset with good placement, sensible levels, and a quiet room can sound clearer than an expensive microphone with poor settings.